Board and Batten Siding Installing Step by Step

Installing Board and Batten Siding Step by Step

Step 1:

If you are not supplying pre-painted materials and buying them raw, you should consider the painting option for  board and batten siding installing . For painting, solvent-based primer and latex coating may be preferable. Painting everywhere and every corner of the Board and Batten ensures that it shows its best resistance to external influences. Using insulation material behind the Board and Battens will have a positive effect and should not be neglected. The properties of the materials used affects many factors such as waterproofing and insulation.

Step 2:

If there is an old coating on the outer surface of the structure which you are going to apply, work should be started by removing it first. Then, it is recommended that the insulation material be removed by the requirements. Protecting existing insulation material is one of the options, but it is recommended to replace it. Recommended materials are asphalt felt (tar paper) and rain screen matte.

Step 3:

After the preliminary studies are completed, the planning of the application to be performed, and the preliminary draft should be established

For installing board and batten, the boards must be assembled first. This material should be placed considering the expansion and contraction conditions. These movements should be allowed. The amount of space between the boards depends on the material to be used. However, some factors should be considered. These factors are the amount of expansion of the board and the length of the battens. Waste materials can be used to adjust the gap. Less than 3”(7,62 cm) is not recommended.

When assembling the boards, planning should be made in such a way as to enable the expansion of the connection boards. Connection elements should be placed near the middle of the boards;

If the board is less than 10”; a single connection element located close to the center will suffice.

If the board is greater than 10”; by dividing the board size by 3, the connection element is placed in the middle two parts.

Battens both 3” and 4” wide; use a single fastener placed in the center of the board at the top, and bottom edges. (matches pattern of boards).

You should not fasten battens directly on the boards but to the underlying studs or cladding between the board gaps. It will allow the board edges to move freely.

Batten fasteners should pass between the board’s gap but should not restrict the movement of the board which is installed over.

It is more logical and robust to drill holes and insert nails into the holes when boards are not installed for nailing.

Step 4:

After the insulation material is detected and selected, its installation process should be started, and it should be added in the rain protection system. In this way, external effects will be minimized.

Step 5:

The water table is installed first. This is a horizontally placed board with a slight inclination. Insect screen is also attached to one side.

Water Table’s bottom edge is aligned with insect screen which is wrapped the bottomed edge of the rain screen drain mat.

Step 6:

When the skirt board and top metal flashing in place, begin installing the boards of your systems.

Starting from a corner, boards are installed. This is done by specifying the intervals between. Make sure that the fasteners are properly seated. Board should be maintained in this way. Windows, doors, etc. Are should be cut and adjusted accordingly. The lining process should be applied to the boards during the cutting phase. After the boards are mounted, an optional coat painting process can be performed.

Step 7:

Install top trim. This phase optionally used for aesthetics. This procedure must be made before placing the battens.

Step 8:

Install the window door sides and screw.

Step 9:

Battens must be continued to install with the fasteners to fit the gaps between them. Screw the screws in such a way as to allow and pay attention to the amount of expansion.

Step 10:

External corners should be installed to provide aesthetics in external corners.

Step 11:

After you install the Board and Battens, a finishing painting process is recommended.

After this steps Board and Batten Installation Phase will be over.

DIY or Hire a Siding Contractor?

Board and Batten siding is a widely used exterior facade in Europe and America. The aesthetic appearance and the fact that it is suitable for that climate is one of the reasons that it can be used. Board and Batten siding is actually a kind of veneer made considering the expansion and contraction principles of the wood material.

One of the trends of today is the DIY(do it yourself) technique which is prevalent because the human being is involved. Board and Batten siding is a kind that can be made, especially as DIY.

Technically speaking; DIY board and batten siding installing is very simple. It consists of two types of wood in different sizes.

It is important in terms of easy availability of the material, and no need for skilled workers. It supports the applicability in correcting mistakes. It is important in the concept of sustainability which is prevalent in the present day. It provides a great advantage for future years. Also, removing and installation are straightforward. Not requires any master.

The material is quite suitable as a cost and, provides a great convenience for the user. Using it as raw material allows the user to shape and paint according to his wishes.

Its durability lasts quite a long time. Being a natural material increases its durability.

In terms of its easy applicability, it takes less time than other exterior materials. This is a big plus for users.

After knowing a little information about the choice of insulation material, and raw material used behind the board and batten, the user is quite likely to do it himself (DIY). A few puff points that need to know that. Where and how to place the connection element. The construction will be easy after the easy qualification.

Connection with connection elements, noting windows and door edges, leaving the opening between boards through expansions and conflicting values.

As a result Board and Batten Siding is a “DIY” could be a good option for  Board and Batten Siding  if you are willing to get tired 🙂

The practitioner can use this type of siding for a long time with its sustainable feature which is the biggest plus of its that saving from the cost and time after a little information accumulation. Therefore, board and batten siding maintains its popularity today. You can also read : Board and Batten Siding Costs